Design Of Inner Ear High Waist Women'S Shoes

As shown in Figure 5 -1-4, this is an inner ear high waist women's shoe with the former Baotou's structure, similar to the basic structure of the three quarter shoes, directly referring to the design rule of the three quarter head.

But the back Gang is longer than the three quarter shoes, which is the characteristic of high waist shoes.

The height of the back band is 80 to lOOmm, and the length of the shoe is 110~115 mm.

At first, we must Cartesian coordinate, and mark the last and height B'points on the vertical axis.

Then drop the K point on the half panel to the horizontal axis, place the C point on the longitudinal axis, the heel bottom sunset at the B'point, and then outline the half panel outline.

On the half panel, 4 basic control lines should be connected to mark the natural stilts.

2. structure design drawing

As shown in figure 5-1-5, the steps of drawing the structural diagram are as follows:

(1) determine the height and the length of the back height in the coordinate B'point, then measure the height of the lOOmm and set the T point, and cross the T point as the vertical axis of the vertical axis.

The Y point at the back end of the last port is set at or above 5mm.

In the rear arc position, C points are added and put 2mm, D points add 3mm, B points add 5mm, and then y points are aligned with a smooth curve with a S shape, which intersects the vertical line across T points to locate T 'point.

Measure the length of the shoe from the T'point 115mm, then raise the point to 7 to lOmm T.

T'T "length is the basic length of the shoe.

(2) to determine the shoe contour, because the shoe is an inner ear shoe, the middle line of the shoe ears should coincide with the back midline of the last face, so it is necessary to connect a curved arc from the T point downward to the back midline.

Then the arc of shoe ears is designed in the range of the angle between the back midline and the shoe line, and then the shoe line is designed.

And control the outer shoe line slightly lower, slightly higher in shoe bosom line, which is highly different in imitation of full back shoes.

(3) the design of the front and rear sides has the shoe line and the rear arc, and the big appearance of the high waist shoe has already come out.

According to the design rules of the three sections, the former Baotou and the former Chinese gang were designed, and the shoe door contour was designed by positioning.

The shoe eye line of high waist shoes is taken at 15mm, the distance between eyes is bigger than that of full shoes, and 5 eyes are identified equally.

The average eye length of high waist shoes and tube boots is between 15 and 20mm.

The shoe ears are disconnected parts. The upper part is narrow and the width is wide. The upper part is taken from the eye line 12 to 15mm, and the lower part of the connecting part is connected with the front part, slightly wider than the upper end.

After the package is designed, the upper point of the rear heel is located 5 to lOmm above the C point, because the point is no longer the location of the shoe.

Or high or low, in order to adjust the proportion of components.

When designing the shoe tongue, the length of the front pressure is 10 to 12mm on the reference length, and the rear end is increased by 7 to lOmm.

Because the upper is higher, the tongue is pointing.

The upper extension will automatically bend, affecting the actual length of the effect.

Therefore, take the length of eye line according to the length of the tongue.

Note that this reference length is the length of the eye line, not the length of the midline.

The amount of tension is controlled to control 14mm, 15mm, 16mm and 17mm from the back to the back.

Make the difference between the inside and outside of the bottom.

From the design of the above high waist shoes, we can understand that after grasping the basic structure design, we only need to control the height and length of the back Gang, and the outline design of other parts is almost the same.

Therefore, determining the control data of the back Gang is one of the key points in designing high waist shoes.